Samsung Tv Senderliste Astra Hotbird
Hello guys, I am a newbie here. I have samsung UE48HU7500 TV and satellite receiver with one dish, 2 LNBs for Hotbird 13E and astra 4a (sirius) 4.8E. With my satellite receiver the channels work just fine. Recently I tried to connect the satellite cable directly to my TV so see how it works. I got 500ish free channels from hotbird only and 0 from sirius. Sorted the channels with the order i wanted. Then switched off the tv.
The next day I switched it on, the channels were there but I was getting 'weak or no signal' while switching between the channels. I checked the cable from back of the TV and it was plugged properly. I, then deleted all the channels and did a new scan. Found all the channels and sorted them. But after switching on the TV again after a while I get the same thing which is too strange. I went through all the LNB setting from the menu and set all the transponder parameters as I see them from my receiver, but.
Most of them just wont get signal at all or get from 27-30% while when connected through the receiver I get mostly above 80%. Another strange thing is.on a specific transponder on my receiver I get 4-5 channels, but entering that transponder's frequency, symbol rate etc I get only 1 channel on my TV which is completely different from what I have on my receiver. I would appreciate if anyone could help me on this to sort the things out. Sincerely, AK. Click to expand.Alright, my apologies. I found more time today and went trough the settings and set up the following. Menu-Broadcasting-channel settings-Satellite system In satellite system menu I done the following: Satellite selection - Hotbird 13E and Astra 4.8E LNB Power- ON LNB settings- Hotbird 13E DiSEqC mode - 2/4 (there were 1/4,2/4,3/4,4/4,toneA,ToneB) Lower LNB Oscillators: 9750 MHz Upper LNB Oscillators: 10600 MHz Tone 22kHz: Auto LNB settings- Astra 4.8E DiSEqC Mode- 1/4 Lower LNB Oscillators: 9750 MHz Upper LNB Oscillators: 10600 MHz Tone 22kHz: Auto With current settings I receive channels from Hotbird with low signal though.maximum at 30%, and nothing from Astra 4.8E.
Although before making changes with DiSEqC, I was able to watch Astra only. I have tried different combinations with DiSEqC settings.
.jpg "Samsung")
Samsung H-Serie Astra 19,2 + Hotbird 13 Grad. SRF-Sender auf Hotbird – Position: 13,0; Download von Samsung tv senderliste auf Freeware.de.
Setting hotbird to 1/2 and astra to 2/4 or 2/4 and 3/4, 3/4 and 4/4, tone A and Tone B etc. But the result is I get max 30% signal strength on either one of the sats. There is a position settings menu as well. By factory default its on OFF. I turned that ON and there are the following options: Positioner Type (options DiSEqC 1.2 and USALS) If you select USALS there are more options to select like: My Longitude ( X X Numbers to set and East or West) My Latitude ( X X Numbers and North or South) Satellite Longitude settings ( User sat 1 0.0 E, user sat 2 0.0 E, User sat 3 0.0 E, user sat 4 0.0 E to set) Sorry, for this essay, just tried to be as clear as possible.
Thanks for the help. Alright, guys.
- Samsung H-Serie Astra 19,2 + Hotbird 13 Grad. SRF-Sender auf Hotbird – Position: 13,0; Download von Samsung tv senderliste auf Freeware.de.
- More Samsung Tv Senderliste Astra Hotbird images.
I have solved almost everything out. Both, Astra and HotBird channels are showing fine, although the signal on specific transponders drops sometimes to as low as 10-12%. I run AUTO tune in full mode for both of the satellites separately and found almost all the channels I needed except 5 of them. Then I tried to run manual transponder search which I have done in past 10-11 years on my receiver successfully, but the parameters I enter for the channels I need get 0% of signal, which is very weird, since they work fine on the receiver right now.
The channels and parameters are as follows: ARM 1TV - HotBird 13E 12520V 27500 3/4 Armenia TV - HotBird 13E 12520V 27500 3/4 1TV RUS - HotBird 13E 12597V 27500 3/4 EuroNews (the multi language one I get on the receiver) - HotBird 13E 12597V 27500 3/4 RBC-TV - HotBird 12520V 27500 3/4 Again, thanks for the help. Dear all, I recently bought a Samsung UHD TV UE48JU6450U which has a built-in satellite tuner.
Samsung Tv Senderliste
I have two LNBs connected via a DiSEqC switch - SPAUN SUR 211F DiSEqC 2.1. The two LNBs are pointing at Astra 19.2 and 28.2.
There are three modes - 1st uncommitted switch, Position (Tone burst) and Option (only DiSEqC. LNB2 is connected to Astra 19.2 and the first one to 28.2. However, in my TV, I only manage to receive one of the two satellites. If I select the 'first uncommitted switch', it finds 28.2 channels and if I choose Position or Option, only 19.2 channels. Any ideas on how I can watch both at the same time? Btw, to give some more information the signal strength with Astra 19.2 is close to 100% while with Astra 28.2 only around 0-5% although I actually the channels just fine! I read on some forums that Samsung TVs don't support 2.1 and I should buy a switch for 1.0.
However, I can't seem to find any 1.0 switch online or in shops. Most are 2.0 and above. Has anyone out there managed to get two satellites working with this TV series or model?
Thanks a lot in advance! Yes two cables. But if the DiSEqC switches are set to 28.2E, then of course you cannot receive 19.2E.
The DiSEqC switches have two (or more) inputs, one from 28.2E and the other from 19.2E but only have one output which goes to the TV, so you can only have either 28E or 19E, not both. The second cable is to allow you to record one programme and watch another on a different TP (from the same satellite group). My TV has two tuners each connected to its own DiSEqC switch and two quad LNBs. If I want to record one channel and watch another on the same TP, then it is likely that only one tuner will be used, But if i want to record and watch from different TPs the two tuners must be used. The TV does this automatically. That makes it more clear. Btw, one quick update.
There was some update to the TV firmware last weekend and it seems I am able to receive both satellites more or less at the same time on the same cable. I am not sure whether it was the firmware upgrade or the new way of searching but here it goes. In the broadcasting source, I had a separate 19.2 input shown (besides Satellite, Cable and Terresterial). When I use that option I am now able to watch all but only 19.2 channels. With the satellite input, I scanned for only Astra 28.2 and it found some more or less all channels. With this setup, I do need to change in the broadcasting settings from 19.2 and Satellite input but then at least I can watch all channels without changing cables or any other settings. TV remembers all channels from both satellites.
If the DiSEqC switch is switching properly, when you select the 28E sat, it will scan that sat group and return a bunch of English language programmes. When you select the 19E group it will scan that one and tune mainly European language programme.
The set will remember all the channels scanned from both sats. If the DiSEqC switch is not switching properly and is permanently set to (say) 19E when you do a scan of 28E, you will get a bunch of channels tuned, but they are NOT from the 28E sat, they are from the 19E sat. This is a fairly common mistake that people make, but I'm not necessarily suggesting that you are making it, just putting it forward as a possibility. But it seems that you have your setup done correctly. The point that I was making earlier was that DiSEqC switch will only select one of its inputs to its output, so you can only 'see' one sat group at the same time.
So you will not be able to (say) record BBC1 from 28E and watch (say) RTL from 19E at the same time. Hi All, I read this post with interest as I have a question re getting two Russian channels on my new LG smart tv (model 28MT495S). I have a 60cm dish with 3 LNBs (Astra, Hotbird and Sirius) that is currently feeding two sat. Boxes and two tvs and on both tvs receiving Astra and Hotbird channels including RTR and 1TVRUS, two Russian channels. Yesterday, I bought a new LG smart tv that has a satellite tuner within it and when I took the sat coax out of the box and screwed in the coax direct to the tv and tuned the two satellites, Astra and Eutelsat Hotbird 13E, I seemed to get all the astra channels but only get 48 channels tuned in on the Eutelsat Hotbird 13E, and the channels are not the same ones getting out of my sat boxes. The two that I especially want are RTR and 1TVRUS. Does anyone know why theses are not coming?
I am uploading a file with a photo of the channel information from the box itself, which says it is on Hotbird 6, 1TVRUS Europ, 12597/V/27500, PID: 2301/2311/2301. In fact, while tuning the Hotbird satellite on the LG tv, I can see when it goes over 125927/V/27500 but it picks up no channel there.
Do you think it is a tv issue, or a location country issue. I checked the country in the satellite boxes, which were installed many years ago by a Latvian installer here in Ireland) and it is set to United Kingdom, but when I switched the LG tv location to UK (instead of Ireland), it only allowed me to tune on the Astra satellite and I wasn't even able to add the Eutelsat Hotbird satellite for tuning. When we bought the tv, I explained to the guy at the store (who also seemed to be eastern EU) that we were mainly trying to get Russian channels, and he quickly told me if we had any problems to try changing location countries, so I tried Latvia, Germany, Poland, and for each of these still getting the same 48 channels, which are pretty awful ones at that. Any held appreciated as it would be good to get rid of my old satellite box and put the cable straight into the smart tv instead as I want to wall mount it.